Respected Sir,

Dream Box Dm 920 UHD

1. After flashing the below latest rescue loader, red light on the front side of the dreambox dm 920 is blinking in red always. Dreambox is not booting & getting into setup menu & unable to get the IP address.

zImage-rescue-3.14-r0-dm920-20200511.bin

2. TV Screen displays dreambox explore more & circle is rotating on the top left corner.

3. If I switch off & switch on the dreambox by pressing the red button for few seconds, dreambox lcd displays waiting for DHCP.

Could you please help me in resolving the same.

Thanks

You need to flash a new image into your box,

Flash our OpenPLi 7.2star image you will find on link below,

DM920UHD OpenPLi 7.2star : http://www.ourdreambox.com/ubbthreads.php?ubb=showflat&Number=21226

Do it, when you have the DHCP on the LCD, as you explained.

TS

Respected sir,

Since, yesterday night, TV Screen displays dreambox discover more & 2 circle(One Big & One Small Circle) is rotating on the top left corner.

I cannot get into the setup menu for identifying the DHCP ip address.

Thanks

Respected Sir,

If I switch off & switch on the dreambox by pressing the red button for few seconds, dreambox lcd displays Rescue Mode waiting for DHCP. & stops there.

Connect to the Mini-USB Service port on the back of the DM920UHD and Putty to enter with the Putty Terminal in Serial mode (from your PC) into the bootloader. It looks like you corrupted something in the box. Naturally your box MUST be connected to the Modem/Router with a RJ45 cable (try to remove and reinsert to see if it gives you an IP address).

If you want I could access your box with Teamviewer 14.x, you need to execute the install file as for private use (not install) and give me the ID+PIN/Pass (via PM naturally), before you will need to have the Putty connected with the mini-USB cable to the box with your computer, and access to the terminal/DM920UHD. I will re-apply the bootloader update that seems to have gone wrong.

Teamviewer : http://www.ourdreambox.com/Teamviewer/TeamViewer_Setup_14.2.2558.exe

Admin

Respected Sir,

The reason for the above problem is, yesterday I started updating the latest rescue loader for dreambox dm 920 via ftp. The file name is shown below:-

zImage-rescue-3.14-r0-dm920-20200511.bin

then i executed the below code into telnet

flash-rescue /tmp/*.bin

after running the above code in telnet,message from telnet was:-

manufacturer id : c2
memory type : 20
memory density : 19
read it ok
comparing 2848 sectors
erasing 2846 sectors
writing 45536 pages
verifying 2846 sectors
flash done


Request you to resolve by Teamviewer. I will give you the ID & Password.

Ok, i will connect to putty with mini usb cable & what are the parameters I need to update in putty, in order to access for terminal.

Sure, once you have the Putty/Terminal working let me know.

The COM Port depends of the one selected by your PC for it, but you should be able to find it on the "hardware section" where you have all hardware elements listed of your computer.

Then the speed must be 115200bps.

So you will have to select the Serial in Putty, and write COM? with the port, COM1, COM2, COM3, etc, then add the 115200 speed.

Once all is setup, start the Teamviewer and advise me, so I can take a look at it and tell/help you.

Admin

Respected,

This is regarding dream box dm 920

After blinking the red light for number of hours (2 days). Yesterday night once again I switched off & switched on & touched my finger on the blinking red light immediately. All of a sudden my dreambox displayed Rescue Mode http://dm920.local.lan/

Hence, I copied & pasted http://dm920.local.lan/ in the browser
& uploaded the below files with the latest firmware into my dreambox & the dreambox got successfully flashed

dreambox-image-deb-dm920-20200515.tar.xz

Could you please suggest, where I was wrong in telnet after transferring the "zImage-rescue-3.14-r0-dm920-20200511.bin" via FTP

then i executed the below code into telnet

flash-rescue /tmp/*.bin

1. Any other code I need to execute in telnet after flash-rescue /tmp/*.bin so that dreambox do not work in backgound.

2. Presently I am using latest dreambox image. As suggested by you in #21373 - 05/20/20 10:24 AM. Whether I can continue to use

My latest Dreambox image

OR

DM920UHD OpenPLi 7.2star : http://www.ourdreambox.com/ubbthreads.php?ubb=showflat&Number=21226


Sir, please suggest.

The OpenPLi 7.2star is working very well on the DM920UHD, so you can no problem use it in your box, we had more than 15 000 downloads on the past 6 weeks.

Admin

Respected Sir,

The below 2 links/site is not reachable

DM920UHD OpenPLi 7.2star : http://www.ourdreambox.com/ubbthreads.php?ubb=showflat&Number=21227

MEGA Original DM900UHD : https://mega.nz/file/2noTAAaY#K9XKfpi9C_CEu7n3OadEypznEP_7p8OIcLSAhEezyM4

Also please provide the link, where to download the last firmware update for "TECHNOMATE NANO 3T Combo"

Thanks