I loaded this software into the Dreambox 7020hd v2,
but now it only boots up a bit.
Secondstage 89 also appears on the LCD screen.
Then it goes back to booting,
Dreambox...DHCP, etc.
After a few minutes, the device shuts down and then restarts with the same cycle.
What should I do now?
I'll just install a different version on the original Dreambox 7020.hd v2.




[url=DM7020HDv2 : openpli-enigma2-9xstar-dm7020hdv2.nfi (Original)]software[/url]

Flash a Dreambox DMM image (DreamOS), then boot it.

This done, then flash the OpenPli DM7020HD v2 image, it should have updated the box properly (drivers, microcode, FPGA...).

Link :
- OpenPLi 8.x : http://openpli8xstar.japhar.net/OpenPLi8xstar/
- OpenPLi 9.x : http://openpli9xstar.japhar.net/OpenPLi9xstar/

TS

I'm loading the original software into the Dreambox release-dm7020hdv2-4.1.0, which works fine. Now I'm going to turn off the receiver. Then put it in a stopmos and load your software.
OpenPLi 9.x: http://openpli9xstar.japhar.net/OpenPLi9xstar/
The software is now loaded. The screen is restarting. Now I'm waiting to see if it continues booting. It can take a while. I'm waiting patiently... the box shuts down again. It restarts... but unfortunately, this didn't help either.
Now I've installed a different version of PLI 12.3. and with that, the Dreambox 7020v2 boots normally again.

I use the openpli 8.x version on my DM7020HDv1, don't have with me the DM7020HDv2 to test... but I did compile it and it was ok when I released the 8.x.

Try to reset also the BIOS of the box, via Telnet... just in case something is wrongly configured there. Remove all tuners as well, we never know that some drivers could fail. I had some issues with a v1, but that was one of the condensators/capacitors (where there is the 3 near to the smartcard reader) that was defective, so power was not enough and box stopping boot/freezing.

I hope that you just flash the image, and not overwrite anything like flashing after a new SSL, etc... that would explain it fails boot.

Try also to telnet to the box IP address, to see if it's a full reboot or only enigma2 that loops... changing and twisting with image always can get it having bad behaviors (like changing the SSL, as the SSL is compiled with the image and linked to the software in the image, so if you use another one the image could have some incompatibilities with the ssl you then flashed after the image. It's important always to use the image with it's built-in ssl and not replace it).

Admin

When loading software into a receiver, it's not the intention that we have to add much ourselves to get the device to boot.
So I won't go any further in the BIOS or make any other additions.
Now, with this 12.3 software, my receiver works fine.

dead dreambox 7020hd v2

Just quickly download the software for Dreambox 7020 HD v2 from your site.

If you have this error it means you flashed the Japhar DM7020HDv1 version without replacing as explained the SSL by the Original one and the driver file (ko), as explained. Recover it with JapharFlasher to flash the SSL included on the link for the patch.

As you can read :
DM7020HD : openpli-enigma2-8xstar-dm7020hd.nfi (Japhar)
Patch to convert to Original box Patch_Original-Japhar_DM7020HDv1.rar

NO CA ERROR / 2nd failed (you have on your video) :
https://photos.app.goo.gl/M7dQhzbk2j9ETRA2A

This error could come also from a bad TPM chip (if it's v2), or if it's v1 a bad sim...

Admin

http://openpli9xstar.japhar.net/OpenPLi9xstar/openpli-enigma2-9xstar-dm7020hdv2.nfi



This one is for an original Dreambox 7020HD V2, right?

Correct, we will have to double check it,

Can you test this one ? OpenPLi 8.xStar ?
http://openpli8xstar.japhar.net/OpenPLi8xstar/openpli-enigma2-8xstar-dm7020hdv2.nfi

Admin

I thought that version didn't work on my Dreambox 7020HD v2 OpenPLi 8.xStar either? It also just kept booting for a small part.

I thought that version didn't work on my Dreambox 7020HD v2 OpenPLi 8.xStar either? It also just kept booting for a small part.

It is very strange, as we tested at least the 8.xStar on a DM7020HDv2 and it worked, and the 9 is based on the same receipes.

I would flash the box clean naturally, be sure that it's not in multi-boot, and directly in the flash. I would also before this, flash a NewNigma2 image, as these update the microcde on the chips (tuners, FPGA etc), to be sure your box is up to date to the drivers used on our OpenPLi. Then flash the openpli, and boot it. If you have the same error, then turn off the box and reboot it again to see if something changes at the second boot (driver microcode FPGA updates ?).

The error of the TPM/Chip should not appear, as this could mean a bad SSL... I talk if the box shows as you told, booting but not fully finishing the boot. Also in that case try to login with telnet to the IP of the box, to see if it booted Linux, and it's more a problem of Enigma2.

Admin

I am currently loading version 7020HD.v2 in the Dreambox

http://openpli8xstar.japhar.net/OpenPLi8xstar/openpli-enigma2-8xstar-dm7020hdv2.nfi

Unfortunately, this one doesn't work either

so I'll just go back to other software that does let the receiver start up.