Thanks

OpenPli 4.0 IPTV by MastaG / Japhar Team with 1300 FREE IPTV Channels and with GStreamer 1.9.0.1b (May 6th 2016)



Changes:

- Latest gstreamer 1.9.0.1 snapshot based on recipes from christophecvr:
* Proper fix for HLS segfault on stop
* Re-enable the rtmp seeking and potential segfault fix
* gstreamer1.0-libav is now built against system ffmpeg instead (this differs from chris recipes) *
* dvbmediasink patches for Vu Solo 4K, hd1265 and hd1500 from oe-alliance
- FFMpeg updated to 3.0.2 and is now installed by default *
- Backports to enigma2 for sh4 (mainly servicemp3.cpp related)
- Fix EPG on sh4 receivers
- exteplayer3 is now installed by default, thank you mx3L and samsamsam *
- gstplayer is now installed by default, thank you mx3L and samsamsam
- Mediatomb is now in the feeds
- MediaPlayer2 is now installed by default, thank you mx3L
- SubsSupport (for MediaPlayer2) is now installed by default, thank you mx3L
- No more russian tuxtxt
- Its now possible to set the debug level again in the UI-settings menu, thank you christophecvr
- Latest enigma2 changes, thank you OpenPLi
- latest openpli-oe-core changes, thank you OpenPLi
- ServiceApp, thank you mx3L !!!

Known issues:
- On spark7162 (and 7111 probably as well) fragmented streams such as hls (m3u8) will skip and freeze a lot.
This happened sometime after the official Gstreamer 1.8.0 release and I didnt found the cause yet.
It is not related to the dvbmediasink since it doesnt happen on mips receivers and the code in the dvbmediasink didnt change.
Configure your streams to play with exteplayer3 instead, read below.
- * On the 64MB Dreambox models (DM800HD, DM800Se and DM500HD) there is not enough space to ship ffmpeg.
This means that exteplayer3 and gstreamer1.0-libav arent installed as well because they depend on ffmpeg.
See my attached guide to copy over the root filesystem to a storage device.
- Some Dreambox remotes may behave very sensitive.
This causes button presses to register multiple times instead of just once.
As a workaround you can adjust the key interval:
Go to: Menu - System - Input devices - dreambox remote control (native).
Set "Change repeat and delay settings" to yes
Set "Interval between keys when repeating:" to 200ms or 300ms.
Press green button (OK)
Now set the same delay for: "dreambox advanced remote control (native)" as well.
- DM800 first boot will take a while, please be patient. The next boot will be faster.

Thanks for the hard work from mx3L and samsamsam you can now play your IPTV streams with exteplayer3 or gstplayer instead of the default dvbmediasink.
Especially using exteplayer3 will give much better performance on playing HLS streams compared to gstreamer + dvbmediasink.
For example, playing DJING underground 720p never worked very well on my DM800HD and now it does

VU+ Solo Ferrari V3 : https://mega.nz/#!whgxgRrQ!FPma5g5i2ZWO8p3Oh7fDjbBqcmiZg3aEJZxVVa8UgJk

Hello
work very good on my vu+ solo V3 ferrari, thanks !!
@+

Hi,I've installed this firmware for Vusolo (ferrari v2) its ok but in Softcam CCcam don't working, why?
in telnet i lauched CCcam -v and i received no error but no video
can you help me? Thanx in advanced

You have to install the Cam software from the JAM 5.2, as every image has it's own scripts. If you install by hand you need to do all properly, or use the ipk from the JAM 5.2. It works fine if you do it properly.

About the "no video" thing, all depends of your configuration, and if you have your subscription card on the slot... so I let you check what helps you with the CCcam.cfg as here we don't support it. We only support good working Linux Images based on Enigma2.

Admin

OK ,, now is all ok !! Anyway write because the CCcam.cfg in another STB was Ok .
I'm write manual wrong CCcam but now with your help is all oK
thanxs forr image is very good !!!

I can't get any channel lists to work with this image, channels show as <n/a>.

I've tried several channel lists several times over, rebooted the box - doesn't wor for me.

That image works fine. Control that you setup properly the satellites. This is v3, try the v2 instead as well as some clones are not capable to run v3 drivers.

Admin

Hello
I will wish to try the IPTV how to do? Should we install a plugin? Have you a tutorial?
Thank you

You already have the list included on the channel-list of the box when you install it first time, so check these IPTV channels included.

Admin