Sim for DM800HDse v2 Clone

Hello,
I am new to the forum and I would like to know which sim card to buy .NC3 Japhar or .NC3 supersim for my DM800HDse V2 clone. ?
Then what OS install on the sim card the NC3 DM800HDse_OS_JapharFerrari_Dual_0009342C33BE_v3.nc3 or other. ?
Which image Openpli IPTV Japhar install on the DM800HDse. ?
Can you explain to me how to properly install all as needed.
Thank you.

Dear Nardo,

You can order your sim on the Forum Team eShop at http://www.japhar.com/japhar/, please indicate that you want it for the DM800HDseV2, as it will come already programmed (but you can always reprogram it yourself later).

Once you will receive it, we will send you all details.

Admin

Hello,
I ordered the sim card and the reader I reported that it is for a clone DM800HDse V2, I hope to receive the right sim card.
Thank you while waiting for the order and to be able to continue the new installation Japhar.

We confirmed, we received your order.

Thank you for your support to the Team,

Admin

Hello,
Thank you I received the sim card Japhar.
Which Openpli IPTV would advise me to install on my DM800HDse clone with the new sim version NC3 (BetaV4).
Thank you
My greetings.

We will email you some images for beta testing, on DM800HDseV2,

Admin

Hi
I have a clone of Dreambox 800SE V2 a Sunray SR4 V2 triple tuner s /c /t2 with sim 2.2 SSL88a .Do you have a Jhaphar sim compatible with my box?And also a tutorial to replace the sim 2.2 safely and some images ?
Tnx for responce

Hello,

Yes, you can replace the sim in your box, by the Japhar Sim for DM800HDseV2, there is a tutorial that is sent to you when you buy it on the eshop of the team, at http://www.japhar.com/japhar/

Admin

Tnx admin
And a question how can I activate the trial tuner to use sattelite and cable tuner.I"ve tried with trial tuner driver 2.0 but no chance to work
tnx

We have a set of drivers for DM800HDseV2 of the Trial/Triple Tuner, so yes it will be available, and you will be able to test once you have Sim+Image Japhar installed in your DM800HDseV2 box.

Admin

Ok great news because with pli img I don't have the trial tuner fully functional. I hope next mounth i make the order but I don't see listed the sim card for 800SE V2 version. And i have a question about the payment, you accept paypall?
Tnx

Just order the DM800HDse and tell us it's for V2,

For payment you need to PM us,

Admin

Hello,
My sim card japhar does not match my original sim card DM800HDse V2 Clone can not use it. ????

Yes, it perfectly fits and matches, read the Tutorial to proceed,

http://www.ourdreambox.com/ubbthreads.php?ubb=showflat&Number=11286#Post11286

Just for your information, 10 years old sims have 8 contacts, new technology sims have 6 contacts, 15 years old have 10-12 contacts, as ISO Standard is and was always 6 contacts (and not 8-12 that were there to just protect the chip that was big silicium piece, but today technology reduced it and 6 contacts are enough to protect it, and are the number of contacts needed for a Smartcard.)

Read here for more informations about Size of Sim cards : http://www.ourdreambox.com/ubbthreads.php?ubb=showflat&Number=12368#Post12368

Admin

Hello,
I started by flashing the file secondstage-dm800se-84-allsim.zip and since I have more IP address but a BIOS error message NO CA FOUND on both cards. More possible to flash, how to recover my original sim card because the boot no longer works what SSL flasher on the card and how do I have the card reader but how to use it I do not have the mode of jobs. Help me to update my DM800HDse Clone in order.
Thank you.

Please reflash your sim with the latest OS for DM800HDseV2, you will find it here :

http://www.ourdreambox.com/ubbthreads.php?ubb=showflat&Number=352#Post352

When you use the secondstage-dm800se-84-allsim, you will never have NO CA FOUND / ERROR... so be sure you really flashed it properly and that the sim is properly inserted on the Sim socket on the motherboard.

You need to do exactly as explained on the Tutorial, step by step and not jump not doing some of the steps. It works 100%, in all conditions.

http://www.ourdreambox.com/ubbthreads.php?ubb=showflat&Number=11286#Post11286

In your case, as you ordered the sim before the new OS release, you will need to flash the July OS to have the box working.

Please do exactly step by step as explained above.

Admin

I managed to retrieve my original sim card but when I want to flash the file secondstage-dm800se-84-allsim.zip I have this message INVALID IMAGE OR OLD VERSION then which of the three files I have to flash first Japhar OS V5 or Japhar Driver V5 or SSL88J? Secondmount-dm800seV2?
Thank you

Hello Nardo,

You need to take the sim and insert it on the GCR2 programmer, and with a PC (WinXP or Win7, or even Win10 it works on it), use the OS file V5, you have 3 files inside .bat, .exe and .nc3. Launch the .bat, it should reset the card and flash it, you could have to do it twice to have loaded properly the new OS v5. You should have a FAQ in PDF included on the topic where is the V5 OS (NC3 Japhar Sim - FAQ v3-Simple).

Then once this is done, you can flash the various files, as explained on the Tutorial.

Admin

I succeeded in flashing the sim card Japhar with OS_v5 and I replaced the old sim card by the new Japhar sim and when I still have the message BIOS NO CA FOUND! Why does not it work? I followed the instructions except that file secondstage-dm800se-84-allsim.zip does not work to flasher the old sim card always the same message INVALID IMAGE (OR OLD VERSION). I do not understand anything anymore ! In the procedure to follow ????.
The files do not work on my clone DM800HDse v2. Thank you for helping me understand.

The secondstage-dm800se-84-allsim.zip perfectly works, you naturally have to unzip it, to then use the .nfi file in it.

As explained in the procedure, you need to have the old sim in the box, press the frontpanel button to set to Flash mode, then flash the box with the ALLSIM SSL. This done, then you turn off the box, replace the Sim and put the Japhar Sim. Then boot the box pressing the frontpanel button to set it to flash mode to flash a Japhar Image from the DM800HDseV2 section. Just for your information... we never told to press the back button to flash something into the box... as that button just loads the Sim2 SSL... so it would never work.

TS

Yes I have decompressed the .zip file and I tried to flash the .nfi file on the original box but this one refuses to flash my box it puts me the following message when I launch the flashing INVALID IMAGE (OR OLD VERSION) and this is the cause I do not know how to move to the next step to replace with the new sim japhar and continue flashing a new japhar image. I have a problem with the file secondstage-dm800se-84-allsim.nfi I think my version secondstage is superior than the 84 and it blocks the flash, I need a version secondstage-dm800se greater than 84 -allsim.nfi.I tested the flash secondstageDM800seV2-SSl88J and this one to flasher my box but to the change of sim the message BIOS NO CA FOUND is displayed. Thank you for your help.

Be careful as I see you mix the DM800HDse (V1) and the DM800HDse (V2) boxes, it's 2 different boxes with different software.

It's normal that if your box is a V2, and you try to load a V1 image/file, it will be rejected with the error "INVALID IMAGE (OR OLD VERSION)"... that's absolutely normal. It's like if you wanted to use on a computer a floppy disk and not a hard disk when you connect to the Hard disk connector.

So as it seems your box is a DM800HDseV2, in that case USE ONLY the files for DM800HDseV2.

You have a section for it, don't use other sections that are not destinated to your box. The only one that has compatible files is this one : http://www.ourdreambox.com/ubbthreads.php?ubb=postlist&Board=49&page=1

Concerning the secondstageDM800seV2-SSl88J, this is needed but will work only if you have the DM800HDseV2 Japhar Sim inserted in the box (otherwise you will have the NO CA ERROR message).

But as explained on the tutorial, and if you failed, as you done, it means you didn't done as explained in the Tutorial...

- Flash the ALLSIM for your box, in your case DM800HDseV2.
- Turn off box
- Remove the old Sim
- Insert the new Sim, Japhar for DM800HDseV2
- Turn on the box and press the frontpanel button to flash a Sim Japhar DM800HDseV2 image, that you find ONLY on this section, http://www.ourdreambox.com/ubbthreads.php?ubb=postlist&Board=49&page=1

Concerning your Sim, be sure you flash the OS v5, and not an older one, ONLY the v5 (for DM800HDseV2) will work.

If you do it AS wrote above, it will be successful, if you do something different or you think being clever not doing one of the steps above, it will... fail as it happens.

Admin

Finally I succeeded, I thank you for the patience that you had to explain to me every day. Now everything works well with your explanations.
Thanks again.

;o), I am very happy, can you let us know where was the point that was not good, so perhaps it happens to other members and we were not enough clear in explaining all ?

Very nice that this is solved, enjoy your new images and DM800HDseV2 second life !

Admin

My difficulty was finding the right Secondstage-dm800sev2_allsim.rar here is the cause. And thank you for your forum and your work on the sim card Japhar. Good continuations.

Thank you for your advise, we will update the Tutorials to have also the DM800HDseV2 links, that is a new OS/Box of last week for Japhar Team and Support ;o)

Admin

Sorry for posting on this thread, but is the Japhar sim for DM800se v1 compatible with the DM8000 se v2 box?
I already have a v1 sim and want to know if I can use it in a v2 box.

Yes, it is compatible, but you will need to reflash it with the DM800HDseV2 Japhar OS,

Admin

Do I need a card reader to do this or can I do it in the box?

You need a PC/SC Reader/Programmer, like the GCR2 we are using, that you can find at http://www.japhar.com/japhar/

TS

Sorry for the delay in reply, but can I use an older reader/programmer like the phoenix smartmouse?

These are not enough reliable to be used, and could destroy the sim card.

You need to use a fully supported PC/SC Smartcard reader, like the GCR2 we are using (and even not all PC/SC are reliable ;o((( ).

The PC/SC Smartcard Readers are used for banking, PKI, Health Card, etc etc, so it should be not too difficult to find one.

Admin

Hi
Please help me to activate trial tuner in my Sunray SR4V2 .Now I have the japhar sim in the box and openpli-enigma2-5Plus-dm800sev2 instaled.I try to install via plugins pannel the correct driver trial tunner but the message is incompatible with the box.How to proceed?
Tnx

You need to install this ipk, for DM800HDseV2,

http://www.ourdreambox.com/ubbthreads.php?ubb=showflat&Number=13324#Post13324

Admin

Hi
I've tried with trialtuner-bobsilvio-compiled_2.0b_all in openpli-enigma2-6Plus-dm800sev2 and no change.Only DVB S2 works.What am I doing wrong? Please help!!
The message is 'refusing to load file tmp/trialtuner-bobsilvio-compiled_2.0b_all as is matches the instaled trialtuner-bobsilvio-compiled_2.0b_all

Reinstall the image, if you played with drivers and installed few, before the right one indicated above, it WILL NOT WORK.

So reinstall a clean image and then install then only the driver indicated above,

Admin

Hi
Is the correct driver 'trialtuner-bobsilvio-compiled_2.0b_all' ?In the link that driver is for V2!
Tnx in advance

Use the driver/ipk from this topic for DM800HDseV2,

http://www.ourdreambox.com/ubbthreads.php?ubb=showflat&Number=13405

Admin

Hi

I am very dissapointed I did exactly as it appears in the post I've tried all kind of img (pli,blackhole etc).

It works only dvbs2. With sim 2.2 the trial tuner was functional.

The driver is exactly the same as for any other box/sim, so you should be in the exact same situation as you were before.

Do you have on the Receiving Sat/Ter Menu the 3 positions ? Sat, Terrestrial and Cable ?

New Installations always get some tricky situations at start then once all is setup properly it works perfectly.

Admin

Menu should be like this,

Yes virtualy i have trial tuner installed but not works. Only dvbs2 work perfect. The dvbc message is 'tune failed' and I can't scan .Do not alow me to put 1 in front of freqvency ...have only 3 digits aviable .Ex 341 fec 6900 quam 64
You have attached my settings that worked perfect with sim 2.2

Ok, did you replaced the cable.xml file in /etc/tuxbox ? Probably the "standard" one is not for your country or is just missing.

See below, I am preparing a "ready to use" image for you and members here with Triple/Trial tuner and A867 USB DVB-T Dongle Support, as well as built-in Wifi, but you will need to add your cable.xml file, as it's not there on the standard installation.

Admin

P.S.: I also checked your settings rar file, and there is no cable.xml file in it.

I have cable in settings see the printscreen in att.I can't automatic scan so how to make cable xml.I don't understand at all what to do

Please use the image below, and add your cable.xml file that is in use for your Cable Operator into /etc/tuxbox,

http://www.ourdreambox.com/ubbthreads.php?ubb=showflat&Number=13422#Post13422

Admin

I have in tuxbox cables xml .You have in attach

Then you should put the .xml file into the /etc/tuxbox folder and reboot your box, and I think it will work,

Admin