How to find out which Sim you have in DM800HDse

Sim Ferrari :

(Sim Ferrari for DM800HDse)



Sim2 Team v2 :

(Sim 2.10 for DM800HDse), the DM800HDseV2 will have Sim 2.20



Sim Chinese Clone A8P :

(Sim Chinese A8P for DM800HDse)



EStar Team v3 :

(Sim 3.0 estar for DM800HDse)



Sim Japhar :

(Sim Japhar NC3 for DM800HDse) Get it Here



BE AWARE :
On DM800HDse V2 Original (and DM500HD V2), you have a chip instead of the Sim card, see below the photo,

Hello, I have a question, which Japhar super sim I bestäla.
I have a Sunray 4 HD see Sim 2.1

Olle

Hello !

You would take the DM800HDse NC3 Japhar, that would be just fine for your box, you can find it at http://www.japhar.com/japhar/

Admin

Thank you so much for the prompt reply.
Olle

Hello I ordered Japhar sim Sunray4 HD SE SIM 2.1.
I asked you what sim suits my box got the following response
You would take the DM800HDse NC3 Japhar, that would be just fine for your box
I got the delivery today and on paper is checked xDM8000HD NC3 (JF) ????
VIP / Memper 1078
Is it okay to proceed with the installation ??

You have PM,

Your paypal payment is quoting a DM8000HD Sim,

Admin

Yes you are right, I beg your pardon.
Is there anything I can do?
Can I send back the sim card?
Or you can reprogram the sim card i have?

How do we make it go fast?

Regards
Olle

Hello Olle,

There is 2 options, yes, don't worry ;o), no problem for it, Hopefully our sim is reprogrammable !

- Fastest (question of seconds to reflash it), you find someone or you check if you have a programmer that is PC/SC Compliant (Windows). All Smartcard readers for Windows are PC/SC. Used for ebanking, health card, bank card, etc.

- You send back, but it will take longer, the time to send and send back.

TS

Hi i have a estarbox es800 hd se with estar sim v3 boot ssl84 im still in oe 1.6 and the best stable image i found is openblackhole 3.2.4 by yassinov im trying to flash oe 2.0 imagen because for example kodidirect new version wont work on 1.6 but i havent been able to get any oe 2.0 images working properly some just give the flashing error wrong architecture in optiflasher and some work but i cant get the wifi to work crashes the box when im searching for networks i know estar stopped the support for the boxes and the sim so my question is i think this sim has some imcompatibilities with 2.0 images so what is the best sim for me to swap

Regards

You are on the Japhar Forum, that supports the Japhar Sim, so definitely we are for the swap to a Japhar NC3 sim card.

You will then have access to the OpenPLi 4.0 image from MastaG/Team Japhar,

You will find it here :
http://www.ourdreambox.com/ubbthreads.php?ubb=showflat&Number=1940#Post1940

And you can get the sim as a member of the forum from here :
http://www.japhar.com/japhar/

Then once you will have the OpenPLi 4.0 image you will be delighted as well as run all what you want that is OE2.0.

Admin

hi just one more question do i have to program the sim with anything or its just swap and thats it and will oe 1.6 also work im using barry allen and im not sure if i cant have mixed oe images to boot because i only have 1.6 images installed all the 2.0 failed or are buggy like i said managed to intall pli 4 but cannot connect wifi

Regards

You receive the sim ready to be used and inserted on the DM.

You will have to do it the way we explained as published on the forum DM800HDse Tutorial http://www.ourdreambox.com/ubbthreads.php?ubb=showflat&Number=2283#Post2283

If you do as explained you will have no problem as this way works 100%.

You can install the images you want from the Japhar DM800HDse section : http://www.ourdreambox.com/ubbthreads.php?ubb=postlist&Board=48&page=1

You will have the OpenPLi 4.0 IPTV working.

Concerning the multiboot, generally only the images from the same generation work, and you cannot mix various images if they have different drivers. So I generally tell it's better to have just one good and working image on the Flash, to have no issues and to have a stable box.

Admin

Hi, i have a DM800HDSE with e-star SIM v.3. To have more up-to-date images I bought the japhar nc3 v2 for dm800hdse, my question is:
1 is the japhar that I bought with my Box compatible?
SIM chip Japhar looks smaller than the e-star chip, is that why I can not get it recognized from the box?
To say I followed the guide but the error is always the same.
Can you help me understand and solve my problem? Thank you

Hello !

Yes, the Japhar Sim is compatible with all the Clone hardware as well as Original hardware.

You must do as explained in the tutorial, and remember that smaller is the chip, newer it is. Very old chips used by estar/ferrari/sim2 are big because technology used is 10-15 years old in their chips, so the die (silicium part) is much bigger and needed big protection.

You can read for more infos here,

http://www.ourdreambox.com/ubbthreads.php?ubb=showflat&Number=12368#Post12368

And the Tutorial for upgrading your box from the old sim to the Japhar, you can read this,

http://www.ourdreambox.com/ubbthreads.php?ubb=showflat&Number=11286#Post11286

Admin

Hello, thanks for the directions.
Takes the second -stage-dm800se-84-allsim but nothing to do does boot the boot but does not load the image
Instead with secondstage-dm800sev2_allsim error the IMAGE FOR ERROR ARCHITECTURE

EStar only produced DM800HDse V1 boxes, so you need to use V1 images/files etc. Not V2.

Once you will have your sim, you will just need to use this link for everything,

http://www.ourdreambox.com/ubbthreads.php?ubb=postlist&Board=48&page=1

For the ALLSIM, it just helps to switch from one sim to another sim, without the NO CA ERROR. But it will NOT work with an image to have the image/video/audio/Tuners.

Please do as explained in the tutorial, line be line, and not jump or miss some of them...

http://www.ourdreambox.com/ubbthreads.php?ubb=showflat&Number=13107#Post13107

Naturally this when you will upgrade from Estar Sim to Japhar Sim... Upgrade means you will REMOVE the old Sim and insert the NEW Sim, Japhar (like when you change GSM/Mobile Operator when you change Sim in your mobile phone).

Admin

Hi, having bought the sim japhar for dm800hdse v2 not suitable for my box, can it be reprogrammed to make it compatible with dm800hdse V1?

Yes, sure, you need to use a PC/SC Programmer/Reader (most Windows smarcard readers are), and you can then reflash it with the DM800HDseV1 OS you can find on the DM800HDse Japhar section here, under the OS section.

http://www.ourdreambox.com/ubbthreads.php?ubb=postlist&Board=67&page=1

Generally this is the Dual OS, Ferrari+Japhar one.

Admin