Download Link :

BIN : http://sources.dreamboxupdate.com/download/7020/secondstage-dm800sev2-89.bin

Hello everyone!
Can you build a new SSL 89.nfi for the dm800sev2?
OpenATV is already using the new secondstage 89.
Or say how it is possible to make one SSL and which program?

I'm all the best to follow you work and you're great!

Greetings.

Bic@

You don't need, the SSL88 is already enough, on the RAR Archive file above you already have these,

secondstage-dm800sev2-88.bin
secondstage-dm800sev2-89.bin

Admin

I managed to repair the no ca error to some extent on my DM 800SEV2 it came with ssl89 before I flashed with a wrong image it uploaded ok with your Japhar 1.1 then I flashed with the allsim NFI via dreambox upgrade via the web says done 100% flashed the when trying to load the genuine image says also 100% when trying to reboot it just hangs up there any idea thanks

If the box doesn't have anymore the NO CA ERROR, now you should be able to flash an original image. What means it hangs up there ? Does it now not show anymore NO CA ERROR ? Then you fixed it. Your actual problem is then the image that could be corrupted.

Original images on this forum for DM800HDseV2 : http://www.ourdreambox.com/ubbthreads.php?ubb=postlist&Board=171&page=1

All our images above are tested and confirmed to work.

Below, you need to test but we cannot guarantee the image works.

OpenATV : http://images.mynonpublic.com/openatv/current/index.php?open=dm800sev2

Admin

The image I tried to flash was from the open ATV 6.1 genuine image says on dreambox upgrade 100% done reboot just hangs up wont reboot I tried to flash a back up of a working image that wont boot up either after flashing if I pull the power of and back on when it fails to boot I get dreambox2ndfaild error with a chip with a warning and a network in lcd think that is same as no ca found error would it be possible to do a ssl 89 would be great thanks

Flash one of our images listed on our Original DM800HDseV2 section, I found out recently that some official images are just corrupted.

Original images on this forum for DM800HDseV2 : http://www.ourdreambox.com/ubbthreads.php?ubb=postlist&Board=171&page=1

Admin

Hello I tried that link for genuine images I cant identify what SSL on them cheers

That's not important, just flash any image from them, these are all confirmed working and booting.

Admin

hi i meant to say what I mean by just hangs there after flashing via dreambox upgrade the ip of the box stays on the LCD the firmware upgrade says rebooting but doesn't do anything that's what I mean by just hangs there as time passes does nothing thanks

Use the JapharFlasher v1.1 just to flash the SSL88 ALLSIM. Reboot the box into Web Interface Flash mode.

Then use the WebInterface (with Browser like Chrome) to flash the full image from that list of our original images we published.

TS

Hi thanks I have flashed the SSL 88 ALLSIM with JapharFlasher says box flashed ox when I disconnect and press dreambox botton in and hold in power on comes up as dreambox 2nd failed I cant get into web interface as I cant get into the stop mode to show the box id any idea

Did you tried to flash then the original SSL88 with JapharFlasher ? Try it and let us know what happens then after reboot.

http://www.ourdreambox.com/ubbthreads.ph...sev2-88.nfi.rar

Attached a SSL89 NFI, try it as well and let us know if it works.

Admin

hi I have connected box with Japhar 1.1 connection ok flash the Allsim 88ssl box flash ok keep power on flash original open ATV genuine image from the link you gave me says box flash successful disconnect power of DM box power back up same result dreambox 2nd failure with a warning sign over a chip and a net cable showing on the LCD display in the Japhar should the net box be ticked or not I have tried it both ways same result also when using Japhar it is in serial mode when flashing is that correct I have left the power on after it said box flashed ok I tried leaving power on and web browser put in ip address and got dreambox firmware on ok it shows box as 87j ssl strange!!

Important point, once flash the SSL, you MUST REBOOT the box into Flash mode again. You cannot just flash the SSL and then immediately after the image as it would mean the first SSL is not "seen/loaded" by the box, and only the image is.

JapharFlasher and DreamUp have inside their own SSL, so it could happen that you have something with an older or different SSL when in rescue mode. But then it will write the NFI file you load.

Did you tired to then flash the original SSL88 and the SSL89 ? What are the results. Try the SSL88 (then reboot and tell us result) and then the SSL89 (then reboot and tell us result).

Did you had this problem also before you flashed the image that got you into NO CA ERROR ? Reason of flashing a new image ? As your chip could have failed and could need replacement (you could remove it and solder a simsocket and install a Japhar Sim, if the chip is dead).

First of all try the SSL88 and SSL89, and tell us for each one the results.

Admin

Hi everyone
Good morning
I have a question. In the display screen in dreambox 800hd se v2 i can see a message following the bootup "Dreambox 2nd failed" how to fix this error.
thank you
Have a wonderful day

Read here,

http://www.ourdreambox.com/ubbthreads.php?ubb=showflat&Number=15214#Post15214

Admin