12427 Members
237 Forums
7732 Topics
23828 Posts
Max Online: 4756 @ 02/20/20 11:12 PM
|
|
|
|
10 registered (Admin, Toysoft, bitgames, kroksy, samochod3, gedis, tester27, haki, piterfree, Smokey),
1316
Guests and
544
Spiders online. |
|
Key:
Admin,
Global Mod,
Mod
|
|
|
|
1
|
2
|
3
|
4
|
5
|
6
|
7
|
|
8
|
9
|
10
|
11
|
12
|
13
|
14
|
|
15
|
16
|
17
|
18
|
19
|
20
|
21
|
|
22
|
23
|
24
|
25
|
26
|
27
|
28
|
|
29
|
30
|
|
|
|
|
|
|
|
|
#3339 - 10/21/15 02:12 AM
Tuner problem with vix v3 image
|
VIP Japhar
journeyman
Registered: 09/02/15
Posts: 77
|
I have done a fresh install of this image!vuduo-Apollo.023-20150917_082001
It works fine at first but after a while i have tune problems if i turn off by switch at back the turn back on sometimes rectifys problem but sometimes not!
sometimes doesnt recognise tuners installed also!
is it image or box what can i try please?
|
|
Top
|
|
|
|
|
|
#3341 - 10/21/15 04:52 AM
Re: Tuner problem with vix v3 image
[Re: sailsy]
|
Japhar Member
Carpal Tunnel
Registered: 10/22/10
Posts: 2639
|
Are you sure to have a Ferrari v3.x box ? Please open and take photo of the security chip... as your problem looks like that your box is not a Ferrari.
TS
_________________________
DM8000, DM800se, DM500HD, DM800HD, DM7025, DM7020s, DM7000, DM500s VU+ Solo, VU+ Uno, VU+ Duo, Kathrein UFS910 Tivusat, TNTSat, Fransat, SSR/TSR, BBC1-2-3/ITV DE-OpenBlackHole 1.4 image : http://www.openblackhole.com/
|
|
Top
|
|
|
|
|
|
#3344 - 10/21/15 07:10 PM
Re: Tuner problem with vix v3 image
[Re: sailsy]
|
VIP Japhar
newbie
Registered: 06/29/14
Posts: 47
Loc: Everywhere
|
I have had trouble with some boxes so too determine if hardware or software issues I try the following. Use Toysofts OpenBlackHole 1.4 and see if you problem still exists. If tuner issues are gone its a software issue with your setup. If it still persists its hardware. OpenBlackhole 1.4 is a good base to check with as always works well with all boxes.
_________________________
DM800
DM800SE
DM800SEV2
VU+ UNO
VU+ DUO
VU+ DUO2
VU+ SOLO2
|
|
Top
|
|
|
|
|
|
#3345 - 10/21/15 11:27 PM
Re: Tuner problem with vix v3 image
[Re: diceman01]
|
VIP Japhar
journeyman
Registered: 09/02/15
Posts: 77
|
Ok I'll try the 1.4 thanks for input!
|
|
Top
|
|
|
|
|
|
#3348 - 10/22/15 03:36 AM
Re: Tuner problem with vix v3 image
[Re: sailsy]
|
VIP Japhar
journeyman
Registered: 09/02/15
Posts: 77
|
Ok there's obviously some kind of hardware problem black hole 1.4 installed ok and channeled scanned ok then did a reboot wouldn't start left it ten mins booted ok!
So where do I look first power supply or security chip?
|
|
Top
|
|
|
|
|
|
#3352 - 10/22/15 09:12 PM
Re: Tuner problem with vix v3 image
[Re: sailsy]
|
VIP Japhar
newbie
Registered: 06/29/14
Posts: 47
Loc: Everywhere
|
PSU is common fault also C807 on main board causes starting issues, but Johnny B is the best person to sort hardware issues. Link to his forum: http://jb8a8f8.com/support/index.php
_________________________
DM800
DM800SE
DM800SEV2
VU+ UNO
VU+ DUO
VU+ DUO2
VU+ SOLO2
|
|
Top
|
|
|
|
|
|
#3356 - 10/23/15 01:22 AM
Re: Tuner problem with vix v3 image
[Re: sailsy]
|
VIPF Japhar
enthusiast
Registered: 03/09/15
Posts: 218
Loc: Netherlands
|
I'm thinking on, check with a terminal as putty why it fails.
And if I think it's a hardware failure, and only when the box is warm, I would try to find the fault with freeze spray, or with a small fan blowing to a sector.
But if it's still have the original C807 cap, I would replace it.
Because this is the number one fault of these boxes.
And if that doesn't help, I would try another psu.
Nevertheless, because you say that it just works with a cold boot, there's a reasonable chance to find it with a fan.
_________________________
Doing nothing leads to nothing. ------------- Please note, for technical support ------------- Will be given here, or on the jb8a8f8 forum and I prefer it in English. Johnny B. Click on the banner if you like to go there.. 
|
|
Top
|
|
|
|
|
|
#4763 - 01/06/16 03:21 AM
Re: Tuner problem with vix v3 image
[Re: Johnny_B]
|
VIP Japhar
journeyman
Registered: 09/02/15
Posts: 77
|
Ok i have changed psu and the c807 cap still have the same problem also tried a different security chip, didnt have much look with a blower!
i have took the board out and had a good look on both sides and noticed this marked by the arrows should there be solder there???
[img]https://mega.nz/#!H99h0RAI!4oQABPE9nEPR5EbgWVarmeds1notcH2goTtDmL7qSO8[/img]
Attachments
Presentation1.jpg (24 downloads)
|
|
Top
|
|
|
|
|
|
#4776 - 01/06/16 05:43 AM
Re: Tuner problem with vix v3 image
[Re: sailsy]
|
VIPF Japhar
enthusiast
Registered: 03/09/15
Posts: 218
Loc: Netherlands
|
That's just the cover, and is already soldered with the other two.
_________________________
Doing nothing leads to nothing. ------------- Please note, for technical support ------------- Will be given here, or on the jb8a8f8 forum and I prefer it in English. Johnny B. Click on the banner if you like to go there..
|
|
Top
|
|
|
|
|
|
|
Previous Topic
Index
