Welcome to Our Dreambox World - Japhar Sim - SuperSim
Forum Stats
12401 Members
237 Forums
7723 Topics
23804 Posts

Max Online: 4756 @ 02/20/20 11:12 PM
Newest Members
djmed, kiki21, nobles, Josef Novak, Mohmmed.59
12401 Registered Users
Who's Online
4 registered (Toysoft, Admin, haki, Warder), 995 Guests and 168 Spiders online.
Key: Admin, Global Mod, Mod
Shout Box

Top Posters
Admin 9876
Toysoft 2634
satsedhu 1713
fairbird 765
ludo19 442
Top Posters (30 Days)
Admin 19
dmr 8
Rtm79 4
Toysoft 3
Sasillo 3
March
M Tu W Th F Sa Su
1 2 3
4 5 6 7 8 9 10
11 12 13 14 15 16 17
18 19 20 21 22 23 24
25 26 27 28 29 30 31
Topic Options
#1624 - 06/07/15 11:10 PM Network issues
Admin Online   content
Japhar Member
Carpal Tunnel

Registered: 10/19/10
Posts: 9876


Attachments
2290.jpg

DM800hd-networkv3.jpg (3 downloads)
dm800-lan2.jpg

Networkconn.jpg (88 downloads)

_________________________

Top
#5443 - 01/26/16 10:42 PM Re: Network issues [Re: Admin]
Rubeneo Offline
journeyman

Registered: 07/27/15
Posts: 52
Hi all,
This is my problem.
When you turn on the power, ethernet lights are fixed, but three / four seconds off. Dreambox 800 starts fine, but internet does not work (attached photo)
http://subefotos.com/ver/?ac2270f1d2ae57ec4b705e4bf3c7a55ao.jpg

I measured the volt as explanation and these are the results (attached photo)

http://subefotos.com/ver/?1f42b3f65df60fcdb9d73ba92b52d7deo.jpg

I'm measuring correctly?

What else can I check?

Thanks


Attachments
01.jpg

02.jpg



Top
#5449 - 01/27/16 06:00 AM Re: Network issues [Re: Admin]
Johnny_B Offline
VIPF Japhar
enthusiast

Registered: 03/09/15
Posts: 218
Loc: Netherlands
Yes it seems that you measure it correctly.

But if you have,
Network, same symptom, with or without network cable both network leds on, then off.
But the L5 inductor and caps are fine..
*When you check the serial port with a terminal program as Hyperterminal or Putty, and you receive garbage.
Replace the Crystal Y1 54.000.

Or, if you have,
Network, same symptom, with or without network cable both network leds on, then off.
But the inductor L5 and caps are fine..
*When you check the serial port with a terminal progam as Hyperterminal or Putty, and you receive nothing.
Replace the u17 rs232 ic and probably also the crystal Y1 54.000.
_________________________
Doing nothing leads to nothing.

------------- Please note, for technical support -------------
Will be given here, or on the jb8a8f8 forum and I prefer it in English.
Johnny B.

Click on the banner if you like to go there..

Top
#5458 - 01/27/16 05:09 PM Re: Network issues [Re: Admin]
Rubeneo Offline
journeyman

Registered: 07/27/15
Posts: 52
Hi Johnny_B

This is the result of Putty:
-------------------------------------------------------------------------
(c) 2007,2008 Dream Multimedia GmbH. All rights reserved.
Dreambox DM800
FIRST STAGE 1.00 {BO23456}

2ND STAGE OK, build #76 (20100419)

0.000 - BCM board setup
{00000126,00000126,00000125,00000124,00000133,00000133}
0.007 - fp init
0.008 - ca init
SW != 9000
error in receive
error during t1 transfer
SW != 9000
error in receive
error during t1 transfer
SW != 9000
error in receive
error during t1 transfer
1.393 - load config
dCA: not existent, loading defaults
1.423 - config loaded.
* press [S] to enter setup
OLED found!
BOOT #76(20100419)
detected jffs2 blocksize: 16kb
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++++++++++++++++++++++++++
dreamupd initialized
Scanning JFFS2 FS: . done.
/flash/bootlogo.elf
bootlogo size: 163059
using 1280x720p (60.00 Hz)
Using the Small jpeg decoder library, Copyright (c) 2006, Luc Saillard <luc@sail lard.org>
parsing JPEG header..
JPEG Size: 1280x720
/flash/vmlinux.gz
<5>Linux version 2.6.18-7.3-dm800 (amedeo@localhost.localdomain) (gcc version 4. 4.3 (GCC) ) #1 Wed Jun 2 18:15:26 CEST 2010
Fetching vars from bootloader... none present, using defaults.
board_init_once: regval=44ac6502, ddr_strap=3, 4 chips, pci_size=2
Detected 256 MB on board
<4>WARNING: read invalid MAC address ff:ff:ff:ff:ff:ff from flash @ 0xbffff824
Default command line =
root=/dev/mtdblock3 rootfstype=jffs2 rw console=null
1 831ffed8 8303c848
g_board_RAM_size=256MB
Options: sata=1 enet=1 emac_1=0 no_mdio=0 docsis=0 ebi_war=0 pci=1 smp=0
CPU revision is: 00020000
Determined physical RAM map:
memory: 10000000 @ 00000000 (usable)
---> memsize from bootloader: 148
User-defined physical RAM map:
node [00000000, 09400000: RAM]
node [09400000, 06c00000: RSVD]
<5>Reserving 108 MB upper memory starting at 09400000
<7>On node 0 totalpages: 65536
<7> DMA zone: 65536 pages, LIFO batch:15
Built 1 zonelists. Total pages: 65536
<5>Kernel command line: root=/dev/mtdblock3 rootfstype=jffs2 rw console=null
before init RAC 0x02a00000 0x00000000
after init RAC 0x02a0000f 0x0fff0000
-------------------------------------------------------------------------------------

I have to remplacer Crystal Y1 54,000.?
Crystal Y1 54,000 = JWT5400?
That exact model ?

http://subefotos.com/ver/?3f717b9fd399e3d74ec01ea8423148e4o.jpg



Attachments
3f717b9fd399e3d74ec01ea8423148e4o.jpg (118 downloads)


Top
#5463 - 01/27/16 11:25 PM Re: Network issues [Re: Admin]
Admin Online   content
Japhar Member
Carpal Tunnel

Registered: 10/19/10
Posts: 9876
This looks strange to me,

Code:
SW != 9000
error in receive
error during t1 transfer
SW != 9000
error in receive
error during t1 transfer
SW != 9000
error in receive
error during t1 transfer


Like if the sim was not communicating properly or was defective. Can you try with another sim ?

If you press the frontpanel button to load an image, connected with the RJ45... how does the box react and shows on Frontpanel LCD ?

Just as example of a working Sim, you need to all all details as on attachments, and not a MAC that is FF:FF:FF:FF:FF:FF:FF:FF.

Code:
WARNING: read invalid MAC address ff:ff:ff:ff:ff:ff from flash @ 0xbffff824


Thank you,

Admin


Attachments
Telnet.jpg

Webif.jpg


_________________________

Top
#5481 - 01/28/16 08:29 AM Re: Network issues [Re: Rubeneo]
Johnny_B Offline
VIPF Japhar
enthusiast

Registered: 03/09/15
Posts: 218
Loc: Netherlands
Based on that you get a normal terminal output, and no boot issues.
Then there is no reason to replace the crystal.

Maybe you need to reset your bios to fabric standard.
But, there are also other reasons why the network fails, even the connector could be the reason.

Se for all the information I have here..
Dm800HD network-issues
_________________________
Doing nothing leads to nothing.

------------- Please note, for technical support -------------
Will be given here, or on the jb8a8f8 forum and I prefer it in English.
Johnny B.

Click on the banner if you like to go there..

Top
#5483 - 01/28/16 05:39 PM Re: Network issues [Re: Johnny_B]
Rubeneo Offline
journeyman

Registered: 07/27/15
Posts: 52
Thanks for your help,
Clicking on the display only appears ** *** STOP ...

Entering the bios with putty, this is what appears
http://subefotos.com/ver/?0300bfe7a7c46fbf3eaa87f2ca3335a1o.jpg

Which option is to do a reset?

Johnny B where start checking the possible failure?

Top
#5484 - 01/28/16 06:38 PM Re: Network issues [Re: Rubeneo]
Johnny_B Offline
VIPF Japhar
enthusiast

Registered: 03/09/15
Posts: 218
Loc: Netherlands
Your Kernel command line is a bit strange, it should be someting as,
console=ttyS0,115200 root=/dev/mtdblock3 rootfstype=jffs2 rw

Reset question, see tab Exit, and Factory default.
_________________________
Doing nothing leads to nothing.

------------- Please note, for technical support -------------
Will be given here, or on the jb8a8f8 forum and I prefer it in English.
Johnny B.

Click on the banner if you like to go there..

Top
#5485 - 01/28/16 07:06 PM Re: Network issues [Re: Johnny_B]
Rubeneo Offline
journeyman

Registered: 07/27/15
Posts: 52
change manual the kernel?
Or install new image?


Top
#5490 - 01/29/16 02:29 AM Re: Network issues [Re: Rubeneo]
Johnny_B Offline
VIPF Japhar
enthusiast

Registered: 03/09/15
Posts: 218
Loc: Netherlands
The Kernel command line should change to,
console=ttyS0,115200 root=/dev/mtdblock3 rootfstype=jffs2 rw
After you have reset the bios to the Factory default.

If not, copy & paste this command line, and save and exit.
Check it after a reboot, if it's still this normal command line.
console=ttyS0,115200 root=/dev/mtdblock3 rootfstype=jffs2 rw

Because yours is wrong, and could be your network issue.




Attachments
Snap1.jpg


_________________________
Doing nothing leads to nothing.

------------- Please note, for technical support -------------
Will be given here, or on the jb8a8f8 forum and I prefer it in English.
Johnny B.

Click on the banner if you like to go there..

Top
#5496 - 01/29/16 06:24 AM Re: Network issues [Re: Admin]
Rubeneo Offline
journeyman

Registered: 07/27/15
Posts: 52
Hi Johnny
I changed the command, option CHANGE COMMAND LINE, disable It must be enabled or disable?
I leave it enabled if you stay in the middle and not just booting process and putty is very slow. This is the text
(c) 2007,2008 Dream Multimedia GmbH. All rights reserved.
Dreambox DM800
FIRST STAGE 1.00 {BO23456}

2ND STAGE OK, build #76 (20100419)

0.000 - BCM board setup
{00000126,00000126,00000125,00000124,00000133,00000133}
0.007 - fp init
0.008 - ca init
SW != 9000
error in receive
error during t1 transfer
SW != 9000
error in receive
error during t1 transfer
SW != 9000
error in receive
error during t1 transfer
1.397 - load config
1.425 - config loaded.
* press [S] to enter setup
OLED found!
BOOT #76(20100419)
detected jffs2 blocksize: 16kb
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++++++++++++++++++++++++++
dreamupd initialized
Scanning JFFS2 FS: . done.
/flash/bootlogo.elf
bootlogo size: 163059
using 1280x720p (60.00 Hz)
Using the Small jpeg decoder library, Copyright (c) 2006, Luc Saillard <luc@saillard.org>
parsing JPEG header..
JPEG Size: 1280x720
/flash/vmlinux.gz
<5>Linux version 2.6.18-7.3-dm800 (amedeo@localhost.localdomain) (gcc version 4.4.3 (GCC) ) #1 Wed Jun 2 18:15:26 CEST 2010
Fetching vars from bootloader... none present, using defaults.
board_init_once: regval=44ac6502, ddr_strap=3, 4 chips, pci_size=2
Detected 256 MB on board
<4>WARNING: read invalid MAC address ff:ff:ff:ff:ff:ff from flash @ 0xbffff824
Default command line =
root=/dev/mtdblock3 rootfstype=jffs2 rw console=null
2 831ffed8 8303c848
g_board_RAM_size=256MB
Options: sata=1 enet=1 emac_1=0 no_mdio=0 docsis=0 ebi_war=0 pci=1 smp=0
CPU revision is: 00020000
Determined physical RAM map:
memory: 10000000 @ 00000000 (usable)
---> memsize from bootloader: 148
User-defined physical RAM map:
node [00000000, 09400000: RAM]
node [09400000, 06c00000: RSVD]
<5>Reserving 108 MB upper memory starting at 09400000
<7>On node 0 totalpages: 65536
<7> DMA zone: 65536 pages, LIFO batch:15
Built 1 zonelists. Total pages: 65536
<5>Kernel command line: console=ttyS0,115200 root=/dev/mtdblock3 rootfstype=jffs2 rw
before init RAC 0x02a00000 0x00000000
after init RAC 0x02a0000f 0x0fff0000
Primary instruction cache 32kB, physically tagged, 2-way, linesize 16 bytes.
Primary data cache 32kB, 2-way, linesize 16 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
timer irq 67 end 57
PID hash table entries: 2048 (order: 11, 8192 bytes)
Found MIPS counter frequency: 149 Mhz
Using 148.501 MHz high precision timer.
Console: colour dummy device 80x25
################## brcm_serial_console_init, sercon=803831a0
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 145024k/262144k available (3192k kernel code, 116956k reserved, 611k data, 148k init, 0k highmem)
Mount-cache hash table entries: 512
Checking for 'wait' instruction... available.
NET: Registered protocol family 16
registering PCI controller with io_map_base unset
registering PCI controller with io_map_base unset
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
SATA: Primary Bus Master Status Register offset = b0520000 + 00000300 = b0520300
SATA: before init Primary Bus Master Status reg = 0x00000000.
SATA: after init Primary Bus Master Status reg = 0x00000020.
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 8192 bind 4096)
TCP reno registered
JFFS2 version 2.2. (NAND) (SUMMARY) (C) 2001-2006 Red Hat, Inc.
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
Broadcom serial driver version 1.00 (2000-11-09) with SERIAL_PCI enabled
Broadcom BCM7401 P31 Ethernet Network Device v2.0 Jun 2 2010 18:14:55
SUNDRY revision = 74010021, have IP Hdr Opt=1
Config Internal PHY Through MDIO: Auto-negotiation timed-out
: 10 MB Half-Duplex (assumed)
dreamelite initialised
ata1: SATA max UDMA/133 cmd 0xB0510000 ctl 0xB0510020 bmdma 0xB0510030 irq 42
scsi0 : sata_svw
ata1: SATA link down (SStatus 4 SControl 300)
ATA: abnormal status 0x7F on port 0xb051001c
Broadcom STB NAND controller (BrcmNand Controller)
B4: NandSelect=40000002, nandConfig=04042300, chipSelect=1
brcmnand_probe: CS1: dev_id=ad76ad76
After: NandSelect=40000002, nandConfig=04042300
NAND Config: Reg=04042300, chipSize=64 MB, blockSize=16K, erase_shift=e
busWidth=1, pageSize=512B, page_shift=9, page_mask=000001ff
timing1 not adjusted: 5363444f
timing2 not adjusted: 00000fc6
BrcmNAND mfg ad 76 Hynix HY27US08121A (dream) 64MB

Found NAND: ACC=00000000, cfg=04042300, flashId=ad76ad76, tim1=5363444f, tim2=00000fc6
BrcmNAND version = 0x0001 64MB @00000000
Found NAND chip on Chip Select 1, chipSize=64MB, usable size=64MB, base=14000000
ACC_CONTROL B4: 00000000
ACC_CONTROL after: 20000000
page_shift=9, bbt_erase_shift=14, chip_shift=26, phys_erase_shift=14
Brcm NAND controller version = 0.1 NAND flash size 64MB @14000000
mtd->oobsize=16, mtd->eccOobSize=16
brcmnand_scan: mtd->oobsize=16
brcmnand_scan: oobavail=12, eccsize=512, writesize=512
brcmnand_scan, eccsize=512, writesize=512, eccsteps=1, ecclevel=15, eccbytes=3
brcmnand_default_bbt: bbt_td = bbt_main_descr
brcmnandCET: Status -> Deferred
numchips=1, size=4000000
Creating 4 MTD partitions on "bcm7xxx-nand.0":
0x0000000000000000-0x0000000004000000 : "complete"
0x0000000000000000-0x0000000000040000 : "loader"
0x0000000000040000-0x0000000000400000 : "boot partition"
0x0000000000400000-0x0000000004000000 : "root partition"
ehci_hcd_brcm_init: Initializing 1 EHCI controller(s)
10 Dec 2004 USB 2.0 'Enhanced' Host Controller (EHCI) Driver (EHCI-brcm-0)
drivers/usb/host/ehci-brcm.c: starting brcm EHCI USB Controller
- USB h/w setup mode <B>
- USB power enable set for active LOW mode
brcm-ehci brcm-ehci.0: BRCM EHCI
brcm-ehci brcm-ehci.0: new USB bus registered, assigned bus number 1
brcm-ehci brcm-ehci.0: irq 62, io mem 0x10480300
brcm-ehci brcm-ehci.0: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ohci_hcd_brcm_init: Initializing 2 OHCI controller(s)
2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (OHCI-brcm-0)
drivers/usb/host/ohci-brcm.c: starting brcm OHCI USB Controller
- Resetting at b0480408
<-- brcm_start_hc
brcm-ohci-0 brcm-ohci-0.0: BRCM OHCI
brcm-ohci-0 brcm-ohci-0.0: new USB bus registered, assigned bus number 2
brcm-ohci-0 brcm-ohci-0.0: irq 63, io mem 0x10480400
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (OHCI-brcm-1)
drivers/usb/host/ohci-brcm.c: starting brcm OHCI USB Controller
- Resetting at b0480508
<-- brcm_start_hc
brcm-ohci-1 brcm-ohci-1.1: BRCM OHCI
brcm-ohci-1 brcm-ohci-1.1: new USB bus registered, assigned bus number 3
brcm-ohci-1 brcm-ohci-1.1: irq 64, io mem 0x10480500
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
i2c /dev entries driver
Advanced Linux Sound Architecture Driver Version 1.0.12rc1 (Thu Jun 22 13:55:50 2006 UTC).
ALSA device list:
No soundcards found.
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Empty flash at 0x019f2030 ends at 0x019f2200
VFS: Mounted root (jffs2 filesystem).
Freeing unused kernel memory: 148k freed
JFFS2 notice: (16) read_dnode: node CRC failed on dnode at 0x19f1fec: read 0xffffffff, calculated 0x14d40b88
INIT: version 2.86 booting
stb_core: module license 'Proprietary' taints kernel.
init lcd
4004728 ms:
59 ms: 27 Starting /etc/rcS.d/S02sysfs...
17 ms: =s
Startting the hotplug events dispatcher
Synthesizing the initial hotplug events
Waiting for /dev to be fully populated
done
3737 ms: 29 Starting /etc/rcS.d/S03udev...
17 ms: =s
17 ms: 31 Starting /etc/rcS.d/S04bootup...
2 ms: 10
mount: mounting /dev/sda1 on /793 ms: 12
media/hdd failed: No such file or directory
19 ms: 14
36 ms: 15
/dev/sda: No such file or direc57 ms: 16
tory
/dev/sda: No such file or direc15 ms: 17
tory
input: dreambox remote control (native) as /class/input/input0
input: dreambox advanced remote control (native) as /class/input/input1
input: dreambox ir keyboard as /class/input/input2
input: dreambox ir mouse as /class/input/input3
enter base init, xvd 20090807, vdc 20080313, rap 20090430, xpt 20080313
kernMemSize : 148 MB
16:651007000 SMCA: controller reset timed out
register adapter
register adapter
register adapter
register adapter
register adapter
input: dreambox front panel as /class/input/input4
HDMI: no device attached
set sb to 3(2)
set fb to 2(-1)
set input to 0
set fb to 2(-1)
bcm_video_analog_port_setup (fmt=6)
SET FORMAT: display[1], format=6
display 0 uses vbi path 1
display 1 uses vbi path 0
HDMI: hotplug handler!
HDMI: no device attached
using 50.00Hz as MonitorRefreshRate
SET FORMAT: display[0], format=24
set fb to 2(0)
bcm_video_analog_port_setup (fmt=6)
SET FORMAT: display[1], format=6
disable wss on display 0
disable wss on display 1
bcmfb: creating surface with pixel format 0x07e48888 (BPXL_eA8_R8_G8_B8)
enable mad
VIDEO0: set fallback framerate to 60000
VIDEO0: set progressive override mode to 1
VIDEO0: set streamtype!
set MPEG2
sw rave disabled!
set ac3 to downmix
set aac to downmix
DVB: registering new adapter (BCM7401).
autodetecting NIMs...
ret: -145
init ALSA!
NTFS driver 2.1.27 [Flags: R/O MODULE].
ud4353 ms: 18
using 50.00Hz as MonitorRefreshRate
SET FORMAT: display[0], format=18
bcm_video_analog_port_setup (fmt=6)
SET FORMAT: display[1], format=6
set current avs auto aspect to 16:9
disable wss on display 0
disable wss on display 1
set sb to 3(1)
688 ms: 19
117 ms: 20
1 ms: 22
2 ms: 23
VIDEO0: set blank to 0
sync is off so we enable it
playback!
total video delay: 0 (0 ms)
VIDEO0: start decode
flush video decoder
VIDEO0 got pts failed !!!! (ret 0)
VIDEO0: first pts 0x0
VIDEO0: framerate changed 3
VIDEO0: resolution changed (1280 720)
VIDEO0: aspect changed 3
set current avs auto aspect to 16:9
disable wss on display 0
disable wss on display 1
set current avs auto aspect to 16:9
disable wss on display 0
disable wss on display 1
set sb to 3(1)
VIDEO0: set blank to 0
VIDEO0: stop decode
VIDEO0: set blank to 0
no decoder left in sync handling so disable xpt_sync
JFFS2 notice: (397) check_node_data: wrong data CRC in data node at 0x02966c00: read 0xd1981f1e, calculated 0xe6de3b30.
5250 ms: 24
2 ms: 25
112 ms: 26
37 ms: 28
67 ms: 29
23 ms: 30
159 ms: 31
134 ms: 32
24 ms: =s
521 ms: 33 Starting /etc/rcS.d/S05dbus-1...
20 ms: =s
80 ms: 35 Starting /etc/rcS.d/S10tpmd...
22 ms: =s
139 ms: 37 Starting /etc/rcS.d/S20modutils.sh...
163 ms: =s
658 ms: 39 Starting /etc/rcS.d/S21avahi-daemon...
23 ms: =s
75 ms: 41 Starting /etc/rcS.d/S38devpts.sh...
21 ms: =s
evd15038 ms: 43 Starting /etc/rcS.d/S40networking...
INIT: Entering runlevel: 3
VIDEO0: set blank to 0
sync is off so we enable it
playback!
total video delay: 0 (0 ms)
VIDEO0: start decode
flush video decoder
VIDEO0: first pts 0x0
VIDEO0: set blank to 0
VIDEO0: stop decode
VIDEO0: set blank to 0
no decoder left in sync handling so disable xpt_sync
bcmfb: enable manual blit
bcmfb: creating surface with pixel format 0x07e48888 (BPXL_eA8_R8_G8_B8)
166187 ms: =s
10 ms: 50
S355 ms: 50
75 ms: 50
40 ms: 50
1387 ms: 50
415 ms: 53
958 ms: 54
354 ms: 55
25 ms: 56
4 ms: 56
473 ms: 56
5 ms: 57
182 ms: 57
754 ms: 57
230 ms: 59
34 ms: 59
5 ms: 59
4 ms: 59
60 ms: 59
43 ms: 59
948 ms: 59
5 ms: 61
1605 ms: 61
tarting system meJFFS2 notice: (16) check_node_data: wrong data CRC in data node at 0x0296e800: read 0xa3c39302, calculated 0xea76f0c6.
ssage bus: Failed to start message bus: The pid file "/var/r

If this disable, the text is

(c) 2007,2008 Dream Multimedia GmbH. All rights reserved.
Dreambox DM800
FIRST STAGE 1.00 {BO23456}

2ND STAGE OK, build #76 (20100419)

0.000 - BCM board setup
{00000126,00000126,00000125,00000124,00000133,00000133}
0.007 - fp init
0.008 - ca init
SW != 9000
error in receive
error during t1 transfer
SW != 9000
error in receive
error during t1 transfer
SW != 9000
error in receive
error during t1 transfer
1.395 - load config
1.423 - config loaded.
* press [S] to enter setup
OLED found!
BOOT #76(20100419)
detected jffs2 blocksize: 16kb
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++++++++++++++++++++++++++
dreamupd initialized
Scanning JFFS2 FS: . done.
/flash/bootlogo.elf
bootlogo size: 163059
using 1280x720p (60.00 Hz)
Using the Small jpeg decoder library, Copyright (c) 2006, Luc Saillard <luc@saillard.org>
parsing JPEG header..
JPEG Size: 1280x720
/flash/vmlinux.gz
<5>Linux version 2.6.18-7.3-dm800 (amedeo@localhost.localdomain) (gcc version 4.4.3 (GCC) ) #1 Wed Jun 2 18:15:26 CEST 2010
Fetching vars from bootloader... none present, using defaults.
board_init_once: regval=44ac6502, ddr_strap=3, 4 chips, pci_size=2
Detected 256 MB on board
<4>WARNING: read invalid MAC address ff:ff:ff:ff:ff:ff from flash @ 0xbffff824
Default command line =
root=/dev/mtdblock3 rootfstype=jffs2 rw console=null
1 831ffed8 8303c848
g_board_RAM_size=256MB
Options: sata=1 enet=1 emac_1=0 no_mdio=0 docsis=0 ebi_war=0 pci=1 smp=0
CPU revision is: 00020000
Determined physical RAM map:
memory: 10000000 @ 00000000 (usable)
---> memsize from bootloader: 148
User-defined physical RAM map:
node [00000000, 09400000: RAM]
node [09400000, 06c00000: RSVD]
<5>Reserving 108 MB upper memory starting at 09400000
<7>On node 0 totalpages: 65536
<7> DMA zone: 65536 pages, LIFO batch:15
Built 1 zonelists. Total pages: 65536
<5>Kernel command line: root=/dev/mtdblock3 rootfstype=jffs2 rw console=null
before init RAC 0x02a00000 0x00000000
after init RAC 0x02a0000f 0x0fff0000


I do not delete the kernel modification appears that you have told me (console=ttyS0,115200 root=/dev/mtdblock3 rootfstype=jffs2 rw

Also if I try to do a reset to factory and setting and not what makes me, me my settings (channels, language ...) still appears

network still does not work

Top
#5500 - 01/29/16 08:30 AM Re: Network issues [Re: Rubeneo]
Johnny_B Offline
VIPF Japhar
enthusiast

Registered: 03/09/15
Posts: 218
Loc: Netherlands
Yeah I have given you the wrong command line.
This one was to see what happens while booting the whole image file.

But the one that should work for the network is these,
console=ttyS0,115200 ip=dhcp root=/dev/nfs rw

See image for a fully overview.


And about the fault..
SW != 9000
error in receive
error during t1 transfer

Use dreamup, with recovery bad sectors and use the serial port.
Sometimes it's better to do it several times until all bad sectors are marked on the nand flash chip.
Use a image file for the process.

However this error may also come from the tuner, try it without.


Attachments
dm800hd-advancedsetup-overview.jpg (10 downloads)

_________________________
Doing nothing leads to nothing.

------------- Please note, for technical support -------------
Will be given here, or on the jb8a8f8 forum and I prefer it in English.
Johnny B.

Click on the banner if you like to go there..

Top
#5503 - 01/29/16 06:22 PM Re: Network issues [Re: Johnny_B]
Rubeneo Offline
journeyman

Registered: 07/27/15
Posts: 52
I modified the line and I have loaded the boot 84b, now the putty tells me the following:


Dreambox DM800
FIRST STAGE 1.00 {BO23456}

2ND STAGE OK, build #84 (2011-09-02)

0.000 - BCM board setup
{00000126,00000126,00000125,00000124,00000133,00000133}
0.007 - fp init
0.008 - ca init
1.107 - load config
1.135 - config loaded.
* press [S] to enter setup
OLED found!
lcd: BOOT #84B
- read config file: /boot/secondstage.conf
detected old jffs2 sig.. disable hw ecc
detected jffs2 blocksize: 16kb
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++++++++++++++++++++++++++
dreamupd initialized
Scanning JFFS2 FS: . done.
find_inode failed for name=secondstage.conf
load: Failed to find inode
- failed to open /boot/secondstage.conf
- failed to open /cf/autorun.bat
lcd: /flash/bootlogo.elf
bootlogo size: 163059
using 1280x720p (60.00 Hz)
Using the Small jpeg decoder library, Copyright (c) 2006, Luc Saillard <luc@saillard.org>
parsing JPEG header..
JPEG Size: 1280x720
lcd: /flash/vmlinux.gz
<5>Linux version 2.6.18-7.3-dm800 (amedeo@localhost.localdomain) (gcc version 4.4.3 (GCC) ) #1 Wed Jun 2 18:15:26 CEST 2010
Fetching vars from bootloader... none present, using defaults.
board_init_once: regval=44ac6502, ddr_strap=3, 4 chips, pci_size=2
Detected 256 MB on board
<4>WARNING: read invalid MAC address ff:ff:ff:ff:ff:ff from flash @ 0xbffff824
Default command line =
root=/dev/mtdblock3 rootfstype=jffs2 rw console=null
2 831ffebc 83029b34
g_board_RAM_size=256MB
Options: sata=1 enet=1 emac_1=0 no_mdio=0 docsis=0 ebi_war=0 pci=1 smp=0
CPU revision is: 00020000
Determined physical RAM map:
memory: 10000000 @ 00000000 (usable)
---> memsize from bootloader: 148
User-defined physical RAM map:
node [00000000, 09400000: RAM]
node [09400000, 06c00000: RSVD]
<5>Reserving 108 MB upper memory starting at 09400000
<7>On node 0 totalpages: 65536
<7> DMA zone: 65536 pages, LIFO batch:15
Built 1 zonelists. Total pages: 65536
<5>Kernel command line: console=ttyS0,115200 ip=dhcp root=/dev/nfs rw
before init RAC 0x02a00000 0x00000000
after init RAC 0x02a0000f 0x0fff0000
Primary instruction cache 32kB, physically tagged, 2-way, linesize 16 bytes.
Primary data cache 32kB, 2-way, linesize 16 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
timer irq 67 end 57
PID hash table entries: 2048 (order: 11, 8192 bytes)
Found MIPS counter frequency: 149 Mhz
Using 148.501 MHz high precision timer.
Console: colour dummy device 80x25
################## brcm_serial_console_init, sercon=803831a0
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 145024k/262144k available (3192k kernel code, 116956k reserved, 611k data, 148k init, 0k highmem)
Mount-cache hash table entries: 512
Checking for 'wait' instruction... available.
NET: Registered protocol family 16
registering PCI controller with io_map_base unset
registering PCI controller with io_map_base unset
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
SATA: Primary Bus Master Status Register offset = b0520000 + 00000300 = b0520300
SATA: before init Primary Bus Master Status reg = 0x00000000.
SATA: after init Primary Bus Master Status reg = 0x00000020.
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 8192 bind 4096)
TCP reno registered
JFFS2 version 2.2. (NAND) (SUMMARY) (C) 2001-2006 Red Hat, Inc.
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
Broadcom serial driver version 1.00 (2000-11-09) with SERIAL_PCI enabled
Broadcom BCM7401 P31 Ethernet Network Device v2.0 Jun 2 2010 18:14:55
SUNDRY revision = 74010021, have IP Hdr Opt=1
Config Internal PHY Through MDIO: Auto-negotiation timed-out
: 10 MB Half-Duplex (assumed)
dreamelite initialised
ata1: SATA max UDMA/133 cmd 0xB0510000 ctl 0xB0510020 bmdma 0xB0510030 irq 42
scsi0 : sata_svw
ata1: SATA link down (SStatus 4 SControl 300)
ATA: abnormal status 0x7F on port 0xb051001c
Broadcom STB NAND controller (BrcmNand Controller)
B4: NandSelect=40000002, nandConfig=04042300, chipSelect=1
brcmnand_probe: CS1: dev_id=ad76ad76
After: NandSelect=40000002, nandConfig=04042300
NAND Config: Reg=04042300, chipSize=64 MB, blockSize=16K, erase_shift=e
busWidth=1, pageSize=512B, page_shift=9, page_mask=000001ff
timing1 not adjusted: 5363444f
timing2 not adjusted: 00000fc6
BrcmNAND mfg ad 76 Hynix HY27US08121A (dream) 64MB

Found NAND: ACC=03000000, cfg=04042300, flashId=ad76ad76, tim1=5363444f, tim2=00000fc6
BrcmNAND version = 0x0001 64MB @00000000
Found NAND chip on Chip Select 1, chipSize=64MB, usable size=64MB, base=14000000
ACC_CONTROL B4: 03000000
ACC_CONTROL after: 23000000
page_shift=9, bbt_erase_shift=14, chip_shift=26, phys_erase_shift=14
Brcm NAND controller version = 0.1 NAND flash size 64MB @14000000
mtd->oobsize=16, mtd->eccOobSize=16
brcmnand_scan: mtd->oobsize=16
brcmnand_scan: oobavail=12, eccsize=512, writesize=512
brcmnand_scan, eccsize=512, writesize=512, eccsteps=1, ecclevel=15, eccbytes=3
brcmnand_default_bbt: bbt_td = bbt_main_descr
brcmnandCET: Status -> Deferred
numchips=1, size=4000000
Creating 4 MTD partitions on "bcm7xxx-nand.0":
0x0000000000000000-0x0000000004000000 : "complete"
0x0000000000000000-0x0000000000040000 : "loader"
0x0000000000040000-0x0000000000400000 : "boot partition"
0x0000000000400000-0x0000000004000000 : "root partition"
ehci_hcd_brcm_init: Initializing 1 EHCI controller(s)
10 Dec 2004 USB 2.0 'Enhanced' Host Controller (EHCI) Driver (EHCI-brcm-0)
drivers/usb/host/ehci-brcm.c: starting brcm EHCI USB Controller
- USB h/w setup mode <B>
- USB power enable set for active LOW mode
brcm-ehci brcm-ehci.0: BRCM EHCI
brcm-ehci brcm-ehci.0: new USB bus registered, assigned bus number 1
brcm-ehci brcm-ehci.0: irq 62, io mem 0x10480300
brcm-ehci brcm-ehci.0: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ohci_hcd_brcm_init: Initializing 2 OHCI controller(s)
2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (OHCI-brcm-0)
drivers/usb/host/ohci-brcm.c: starting brcm OHCI USB Controller
- Resetting at b0480408
<-- brcm_start_hc
brcm-ohci-0 brcm-ohci-0.0: BRCM OHCI
brcm-ohci-0 brcm-ohci-0.0: new USB bus registered, assigned bus number 2
brcm-ohci-0 brcm-ohci-0.0: irq 63, io mem 0x10480400
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (OHCI-brcm-1)
drivers/usb/host/ohci-brcm.c: starting brcm OHCI USB Controller
- Resetting at b0480508
<-- brcm_start_hc
brcm-ohci-1 brcm-ohci-1.1: BRCM OHCI
brcm-ohci-1 brcm-ohci-1.1: new USB bus registered, assigned bus number 3
brcm-ohci-1 brcm-ohci-1.1: irq 64, io mem 0x10480500
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
i2c /dev entries driver
Advanced Linux Sound Architecture Driver Version 1.0.12rc1 (Thu Jun 22 13:55:50 2006 UTC).
ALSA device list:
No soundcards found.
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Sending DHCP requests ...... timed out!
IP-Config: Reopening network devices...
Sending DHCP requests ...... timed out!
IP-Config: Reopening network devices...
Sending DHCP requests .....

I'll upload a image and say the results, but the process is long.
By the way, his deputy did not leave it open

dm800hd-advancedsetup-overview.jpg (4 Cargas)

Top
#5506 - 01/29/16 08:24 PM Re: Network issues [Re: Admin]
Rubeneo Offline
journeyman

Registered: 07/27/15
Posts: 52
I tried to install a new image and the message is always 14:42:29 Flashing failed (!!! 010 INVALID IMAGE (OR OLD VERSION)), box will be unusable now!!

what recommended that image, the boot that I've put is sim201_ssl84b.nfi

Top
#5509 - 01/29/16 10:41 PM Re: Network issues [Re: Rubeneo]
Johnny_B Offline
VIPF Japhar
enthusiast

Registered: 03/09/15
Posts: 218
Loc: Netherlands
Flashing failed could happen when you use a browser to upload the file, or a older dream-up.
Best is to try it with japhar flasher, or try my Software-dm800hd-sim2-openpli4-ssl84d package which contains the bootloader sim201_ssl84D.nfi and (old) image file openpli-4.0-beta-dm800-20140316-sim2-ssl84d.nfi and DreamUP v1.3.3.4.

It can often also be fixed with optiflasher.
But I assume you use the dm sim2.01 sim card, because the software I give is only suitable for this type sim card.

Network error Sending DHCP requests ...... timed out!
This could mean that your network isn't working, it could be a hardware problem with the dreambox.
However, be sure that you connect your network cable to a dhcp network.
Also be sure that your network cable has no issues.
_________________________
Doing nothing leads to nothing.

------------- Please note, for technical support -------------
Will be given here, or on the jb8a8f8 forum and I prefer it in English.
Johnny B.

Click on the banner if you like to go there..

Top
#5515 - 01/30/16 05:27 AM Re: Network issues [Re: Johnny_B]
Rubeneo Offline
journeyman

Registered: 07/27/15
Posts: 52
Hello Johnny
On cable dhcp, all that is fine. Checked with other dream800 and I assigned ip.

I tried with his image and after an hour, he has become the message ((!!! 010 INVALID IMAGE (OR OLD VERSION)), box will be unusable now!!)

The image takes is Blackhole dreamelite 1.33d v3 sim2.01

n the menu of that image I have to do a reset, but as usual

with putty, with these options I get this

option Change Command Line [ENABLED ] &#9618;Kernel Command Line [console=ttyS0,115200 ip=dhcp root=/dev/nfs rw ]

and reboot, putty tells me the following

(c) 2007,2008 Dream Multimedia GmbH. All rights reserved.
Dreambox DM800
FIRST STAGE 1.00 {BO23456}

2ND STAGE OK, build #84D(2011-09-02)

0.000 - BCM board setup
{00000126,00000126,00000125,00000124,00000133,00000133}
0.007 - fp init
0.008 - ca init
0.945 - load config
0.973 - config loaded.
* press [S] to enter setup
OLED found!
lcd: BOOT #84D
- read config file: /boot/secondstage.conf
detected old jffs2 sig.. disable hw ecc
detected jffs2 blocksize: 16kb
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++++++++++++++++++++++++++
dreamupd initialized
Scanning JFFS2 FS: . done.
find_inode failed for name=secondstage.conf
load: Failed to find inode
- failed to open /boot/secondstage.conf
- failed to open /cf/autorun.bat
lcd: /flash/bootlogo.elf
bootlogo size: 163059
using 1280x720p (60.00 Hz)
Using the Small jpeg decoder library, Copyright (c) 2006, Luc Saillard <luc@saillard.org>
parsing JPEG header..
JPEG Size: 1280x720
lcd: /flash/vmlinux.gz
<5>Linux version 2.6.18-7.3-dm800 (amedeo@localhost.localdomain) (gcc version 4.4.3 (GCC) ) #1 Wed Jun 2 18:15:26 CEST 2010
Fetching vars from bootloader... none present, using defaults.
board_init_once: regval=44ac6502, ddr_strap=3, 4 chips, pci_size=2
Detected 256 MB on board
<4>WARNING: read invalid MAC address ff:ff:ff:ff:ff:ff from flash @ 0xbffff824
Default command line =
root=/dev/mtdblock3 rootfstype=jffs2 rw console=null
2 831ffebc 83029b34
g_board_RAM_size=256MB
Options: sata=1 enet=1 emac_1=0 no_mdio=0 docsis=0 ebi_war=0 pci=1 smp=0
CPU revision is: 00020000
Determined physical RAM map:
memory: 10000000 @ 00000000 (usable)
---> memsize from bootloader: 148
User-defined physical RAM map:
node [00000000, 09400000: RAM]
node [09400000, 06c00000: RSVD]
<5>Reserving 108 MB upper memory starting at 09400000
<7>On node 0 totalpages: 65536
<7> DMA zone: 65536 pages, LIFO batch:15
Built 1 zonelists. Total pages: 65536
<5>Kernel command line: console=ttyS0,115200 ip=dhcp root=/dev/nfs rw
before init RAC 0x02a00000 0x00000000
after init RAC 0x02a0000f 0x0fff0000
Primary instruction cache 32kB, physically tagged, 2-way, linesize 16 bytes.
Primary data cache 32kB, 2-way, linesize 16 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
timer irq 67 end 57
PID hash table entries: 2048 (order: 11, 8192 bytes)
Found MIPS counter frequency: 149 Mhz
Using 148.501 MHz high precision timer.
Console: colour dummy device 80x25
################## brcm_serial_console_init, sercon=803831a0
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 145024k/262144k available (3192k kernel code, 116956k reserved, 611k data, 148k init, 0k highmem)
Mount-cache hash table entries: 512
Checking for 'wait' instruction... available.
NET: Registered protocol family 16
registering PCI controller with io_map_base unset
registering PCI controller with io_map_base unset
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
SATA: Primary Bus Master Status Register offset = b0520000 + 00000300 = b0520300
SATA: before init Primary Bus Master Status reg = 0x00000000.
SATA: after init Primary Bus Master Status reg = 0x00000020.
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 8192 bind 4096)
TCP reno registered
JFFS2 version 2.2. (NAND) (SUMMARY) (C) 2001-2006 Red Hat, Inc.
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
Broadcom serial driver version 1.00 (2000-11-09) with SERIAL_PCI enabled
Broadcom BCM7401 P31 Ethernet Network Device v2.0 Jun 2 2010 18:14:55
SUNDRY revision = 74010021, have IP Hdr Opt=1
Config Internal PHY Through MDIO: Auto-negotiation timed-out
: 10 MB Half-Duplex (assumed)
dreamelite initialised
ata1: SATA max UDMA/133 cmd 0xB0510000 ctl 0xB0510020 bmdma 0xB0510030 irq 42
scsi0 : sata_svw
ata1: SATA link down (SStatus 4 SControl 300)
ATA: abnormal status 0x7F on port 0xb051001c
Broadcom STB NAND controller (BrcmNand Controller)
B4: NandSelect=40000002, nandConfig=04042300, chipSelect=1
brcmnand_probe: CS1: dev_id=ad76ad76
After: NandSelect=40000002, nandConfig=04042300
NAND Config: Reg=04042300, chipSize=64 MB, blockSize=16K, erase_shift=e
busWidth=1, pageSize=512B, page_shift=9, page_mask=000001ff
timing1 not adjusted: 5363444f
timing2 not adjusted: 00000fc6
BrcmNAND mfg ad 76 Hynix HY27US08121A (dream) 64MB

Found NAND: ACC=03000000, cfg=04042300, flashId=ad76ad76, tim1=5363444f, tim2=00000fc6
BrcmNAND version = 0x0001 64MB @00000000
Found NAND chip on Chip Select 1, chipSize=64MB, usable size=64MB, base=14000000
ACC_CONTROL B4: 03000000
ACC_CONTROL after: 23000000
page_shift=9, bbt_erase_shift=14, chip_shift=26, phys_erase_shift=14
Brcm NAND controller version = 0.1 NAND flash size 64MB @14000000
mtd->oobsize=16, mtd->eccOobSize=16
brcmnand_scan: mtd->oobsize=16
brcmnand_scan: oobavail=12, eccsize=512, writesize=512
brcmnand_scan, eccsize=512, writesize=512, eccsteps=1, ecclevel=15, eccbytes=3
brcmnand_default_bbt: bbt_td = bbt_main_descr
brcmnandCET: Status -> Deferred
numchips=1, size=4000000
Creating 4 MTD partitions on "bcm7xxx-nand.0":
0x0000000000000000-0x0000000004000000 : "complete"
0x0000000000000000-0x0000000000040000 : "loader"
0x0000000000040000-0x0000000000400000 : "boot partition"
0x0000000000400000-0x0000000004000000 : "root partition"
ehci_hcd_brcm_init: Initializing 1 EHCI controller(s)
10 Dec 2004 USB 2.0 'Enhanced' Host Controller (EHCI) Driver (EHCI-brcm-0)
drivers/usb/host/ehci-brcm.c: starting brcm EHCI USB Controller
- USB h/w setup mode <B>
- USB power enable set for active LOW mode
brcm-ehci brcm-ehci.0: BRCM EHCI
brcm-ehci brcm-ehci.0: new USB bus registered, assigned bus number 1
brcm-ehci brcm-ehci.0: irq 62, io mem 0x10480300
brcm-ehci brcm-ehci.0: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ohci_hcd_brcm_init: Initializing 2 OHCI controller(s)
2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (OHCI-brcm-0)
drivers/usb/host/ohci-brcm.c: starting brcm OHCI USB Controller
- Resetting at b0480408
<-- brcm_start_hc
brcm-ohci-0 brcm-ohci-0.0: BRCM OHCI
brcm-ohci-0 brcm-ohci-0.0: new USB bus registered, assigned bus number 2
brcm-ohci-0 brcm-ohci-0.0: irq 63, io mem 0x10480400
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (OHCI-brcm-1)
drivers/usb/host/ohci-brcm.c: starting brcm OHCI USB Controller
- Resetting at b0480508
<-- brcm_start_hc
brcm-ohci-1 brcm-ohci-1.1: BRCM OHCI
brcm-ohci-1 brcm-ohci-1.1: new USB bus registered, assigned bus number 3
brcm-ohci-1 brcm-ohci-1.1: irq 64, io mem 0x10480500
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
i2c /dev entries driver
Advanced Linux Sound Architecture Driver Version 1.0.12rc1 (Thu Jun 22 13:55:50 2006 UTC).
ALSA device list:
No soundcards found.
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Sending DHCP requests ...... timed out!
IP-Config: Reopening network devices...
Sending DHCP requests ...... timed out!
IP-Config: Reopening network devices...
Sending DHCP requests ...... timed out!
IP-Config: Reopening network devices...


and will not start the image stays in dhcp ... /flash/vmlinuz.gz

but if I put this setting if you boot image

Change Command Line [DISABLED ] &#9618;Kernel Command Line [console=ttyS0,115200 ip=dhcp root=/dev/nfs rw ]


Dreambox DM800
FIRST STAGE 1.00 {BO23456}

2ND STAGE OK, build #84D(2011-09-02)

0.000 - BCM board setup
{00000126,00000126,00000125,00000124,00000133,00000133}
0.007 - fp init
0.008 - ca init
0.945 - load config
0.972 - config loaded.
* press [S] to enter setup
OLED found!
lcd: BOOT #84D
- read config file: /boot/secondstage.conf
detected old jffs2 sig.. disable hw ecc
detected jffs2 blocksize: 16kb
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++++++++++++++++++++++++++
dreamupd initialized
Scanning JFFS2 FS: . done.
find_inode failed for name=secondstage.conf
load: Failed to find inode
- failed to open /boot/secondstage.conf
- failed to open /cf/autorun.bat
lcd: /flash/bootlogo.elf
bootlogo size: 163059
using 1280x720p (60.00 Hz)
Using the Small jpeg decoder library, Copyright (c) 2006, Luc Saillard <luc@saillard.org>
parsing JPEG header..
JPEG Size: 1280x720
lcd: /flash/vmlinux.gz
<5>Linux version 2.6.18-7.3-dm800 (amedeo@localhost.localdomain) (gcc version 4.4.3 (GCC) ) #1 Wed Jun 2 18:15:26 CEST 2010
Fetching vars from bootloader... none present, using defaults.
board_init_once: regval=44ac6502, ddr_strap=3, 4 chips, pci_size=2
Detected 256 MB on board
<4>WARNING: read invalid MAC address ff:ff:ff:ff:ff:ff from flash @ 0xbffff824
Default command line =
root=/dev/mtdblock3 rootfstype=jffs2 rw console=null
1 831ffebc 83029b34
g_board_RAM_size=256MB
Options: sata=1 enet=1 emac_1=0 no_mdio=0 docsis=0 ebi_war=0 pci=1 smp=0
CPU revision is: 00020000
Determined physical RAM map:
memory: 10000000 @ 00000000 (usable)
---> memsize from bootloader: 148
User-defined physical RAM map:
node [00000000, 09400000: RAM]
node [09400000, 06c00000: RSVD]
<5>Reserving 108 MB upper memory starting at 09400000
<7>On node 0 totalpages: 65536
<7> DMA zone: 65536 pages, LIFO batch:15
Built 1 zonelists. Total pages: 65536
<5>Kernel command line: root=/dev/mtdblock3 rootfstype=jffs2 rw console=null
before init RAC 0x02a00000 0x00000000
after init RAC 0x02a0000f 0x0fff0000


but the network does not work, the two lights go on but after three seconds off

any suggestions?

Thank you my friend

Top
#5519 - 01/30/16 10:02 AM Re: Network issues [Re: Rubeneo]
Johnny_B Offline
VIPF Japhar
enthusiast

Registered: 03/09/15
Posts: 218
Loc: Netherlands
I'm beginning to think at a cpu issue, but if you measure the Rx/Tx +/- print lines at voltage and ohm, you should measure a issue with it.

Maybe you see some voltage drop, or strange ohm value.

In any case, see this information,
http://jb8a8f8.com/support/index.php?attachments/dm800hd-networkv3-jpg.58/

And do some measurements on the network circuit.
But remember, the ohm values are measured between the ground and the measuring point.

However, to do a real ohms measurement for checking the cpu connections Rx/Tx +/-.
You need to remove the network connector from the motherboard.
And also the four resistors R132 to R134.
If you do that, than the ohm value from the Rx/Tx +/- should be in the same Ohms range.

But, it does not have to be a cpu issue, the network connector has internal coils and some other parts.
Suppose that one coil connection has been broken, than you get also this symptoms.

In that case you must replace this network connector for a new one.

Other thing that it could be is one of the ceramic caps C121/C122
But if one of them is shorted, you should notice it by measurements.
_________________________
Doing nothing leads to nothing.

------------- Please note, for technical support -------------
Will be given here, or on the jb8a8f8 forum and I prefer it in English.
Johnny B.

Click on the banner if you like to go there..

Top
#7373 - 04/02/16 04:07 AM Re: Network issues [Re: Admin]
Rufino Offline
stranger

Registered: 03/31/16
Posts: 2
Hi Johny,
nice to contact you again.
I checked all the circuits and apparently are OK.
U10, 1Y1 and 1Y2, are giving 0.169V and 0.175V and after 15 seconds they give 3.5V.Then leds go OFF.
What do you think?
Software problems or I need to change U10?
Kind Regards and good weekend.
Rufino

Top
#7375 - 04/02/16 05:57 AM Re: Network issues [Re: Admin]
Johnny_B Offline
VIPF Japhar
enthusiast

Registered: 03/09/15
Posts: 218
Loc: Netherlands
Hi Rufino,

Assuming that the box further works well.

Network problems by software, is possible.
Best is to always try another image file before thinking of a hardware failure.

The U10 LVC244A, it's possible because the led part data goes trough this chip.
When this failed, it could influence the working of the network port.

Further, it's also possible that it is a crystal issue, more about this see/read here.

_________________________
Doing nothing leads to nothing.

------------- Please note, for technical support -------------
Will be given here, or on the jb8a8f8 forum and I prefer it in English.
Johnny B.

Click on the banner if you like to go there..

Top
#7555 - 04/10/16 12:35 AM Re: Network issues [Re: Johnny_B]
Rufino Offline
stranger

Registered: 03/31/16
Posts: 2
Hi Johny,
double checking all the resistors and capacitors around U6, I found C98, that instead of getting 0,7v IN, it gets 2,1V, perhaps you could help to trace the origine of problems with this information.Good weekend.
Rufino

Top
#7565 - 04/10/16 06:44 AM Re: Network issues [Re: Rufino]
Johnny_B Offline
VIPF Japhar
enthusiast

Registered: 03/09/15
Posts: 218
Loc: Netherlands
One side of the c98 is going to the C100 and the U6 Vc2 pin 10.
THe other side is going to a resistor R114, this resistor goes to ground.

I have here a basic schematic of the U6, here is the C98 the C7 and the C100 the C8.
Maybe there is some issue with one of the caps, bad soldered or something.



Attachments
dm800hd-u6-5v-3.3v-basicschematic.jpg (10 downloads)

_________________________
Doing nothing leads to nothing.

------------- Please note, for technical support -------------
Will be given here, or on the jb8a8f8 forum and I prefer it in English.
Johnny B.

Click on the banner if you like to go there..

Top



Moderator:  fairbird, Johnny_B 
New Topics
ERROR after flashing OpenPLi 8.X star 20230624
by Sasillo
03/25/24 06:27 PM
Fatal: Target device '/dev/dreambox-rootf
s' is not

by Admin
03/22/24 02:45 PM
EchoStar wins DoD extensions for private 5G
by Admin
03/19/24 02:56 PM
DM900 red light
by slavekpl
03/17/24 03:42 PM
openpli-enigma2-8xst
ar-dm820 epgimport not install

by dmr
03/13/24 09:09 AM
openpli-20240306-GCC
-13.2-dm820

by dmr
03/12/24 01:01 PM
Build your own OSCam... Ubuntu 18 and 22 svn11737
by Admin
03/04/24 10:37 PM
EchoStar bleeds Boost Mobile subscribers
by Admin
03/04/24 04:35 PM
Old DM800HDpvr
by Rtm79
03/03/24 06:32 PM
Saluti
by Rtm79
03/03/24 06:19 PM
DM7020HD : OpenPLi 8.xStar 20240303 GSt 1.20.5
by Admin
03/03/24 12:57 PM
DM7020HD : OpenPLi 8.xStar 20240303 GSt 1.20.5
by Admin
03/03/24 12:57 PM